Highly Compact in design and so simple at the same time. Most reliable and efficient performer. An indispensible equipment for Scientific Labs, R&D centres, Pilot Plants and host of industrial units where it is used for vacuum loading and lifting. Available in single as well as in double stage.
Applications »
Vacuum Creation, Filling, drying, Lifting, Forming, Filteration, Distillation, Annealing, Impregnation, Dehydration, Sublimation, Film Coating & many more.
These are Direct Drive double stage, oil sealed rotary high vacuum pumps wherein, state of the art technique has been adopted to ensure proper alignment and the fine setting of each and every component Used, remain ever undisturbed. These are designed to work non-stop without any problem, for a long period of time and come with in built NRV. These are lightweight handy and can conveniently be used for outdoor jobs.
Unlike oil sealed ones, water - ring vacuum pumps are capable of creating vacuum up to 710mm Hg only which is far less than what can be achieved by the former . But still are preferred in chemical and pharmaceutical industries. These prove economical and require less maintenance. Water is used in place of costly oil and no hassle of frequent oil changing. Requires less energy to run and enjoys longer life. Even noise otherwise create no pollution , no fumes and produce every little nosie. Higher vacuum through them can also be achieved when made to work as backing pumps in systems. Suit all applications covered by oil sealed pumps.
Rotary Vane Vacuum Pressure Pumps
Self lubricated and easily maintainable for efficient and care free sustion and pressure needs. These have low oil consumption and are designed for self lubrication fo all the important points. The oil thus used does not contaminate the air, but is baffled from the exhaust, gets collected & returns to the oil chamber and serves for long.
These are widely used for vacuum distillation, extraction, filtration, bottle filling, drying, glass blowing, pharmaceutical, food processing, vacuum forming and blister packing applications.
These are more compact handy, portable, lighter in weight and hence are economically more viable for humble applications. Also these are best suited to OEM's for incorporating them in their industrial units and plants.
Applications »
Filtration, Distillation, evaporation, drying, condensation, sterilization, pharmaceutical, food and confectionary.
Self lubricated and easily maintainable for efficient and care free sustion and pressure needs. These have low oil consumption and are designed for self lubrication fo all the important points. The oil thus used does not contaminate the air, but is baffled from the exhaust, gets collected & returns to the oil chamber and serves for long.
These are widely used for vacuum distillation, extraction, filtration, bottle filling, drying, glass blowing, pharmaceutical, food processing, vacuum forming and blister packing applications.
Revolutionary substitute for ordinary Blowers when large and forceful suction and pressure capabilities are required in agitation of chemicals. Also useful for electroplating, bubbling air through liquid, dust collecting, vacuum cleaning, effluent Treatment and pneumatic conveying etc. These are maintenance free and noiseless because of zero friction and minimum vibration. Completely wear and tear free also as no two parts rub each other and hence economical too. They are capable of doing big jobs with less power.
Diaphargm type vacuum / pressure pumps are 100 % oil free, wherein not even a single drop of oil is used. These are boon for vacuum and pressure application, where even slightest environmental contamination through oil mist is forbidden.
Applications »
Diaphargm type vacuum / pressure pumps are 100 % oil free, wherein not even a single drop of oil is used. These are boon for vacuum and pressure application, where even slightest environmental contamination through oil mist is forbidden.
Applications »
These are single stroke. Air-cooled reciprocating units available in single and double stage configuration and can achieve vacuum upto 29.6" Hg (752 mm Hg).
These are quite reliable and maintenance free pumps. Proving a boon for application where in oil mist contamination is not at all acceptable.
Applications »
Distillation, vacuum forming, paper handling, food processing, filtration, sugar industries, hospitals vacuum impregnation, dairies etc.
Roots air blower / twin lobe compressor is a positive displacement, constant volume machine to operate against varying pressures. With each revolution, the compressor delivers a metered amount of air measured at inlet conditions. Operating at a constant speed against almost constant pressure, it delivers constant stream of pressurized air flow. No contamination, no oil, no spring, no valves or vanes, no internal contact of any parts and hence is free of wear and tear.
Applications »
Water treatment plants, cement, fertilizers, grain, flour & sugar industries, electroplating, gas boosting, liquid agitation and sewage disposal etc
The volumetric performance of the conventional vacuum pumps becomes very poor in low pressure operations. Since twin lobe mechanical boosters are capable of handling large quantity of air even at this stage, they are bought in conjugation with the existing vacuum pump to boost its performance both volume and vacuum wise.
Combined energy required by this system is far less then that of any single pump would had consumed for the equivalent job. Since the boosters are totally free of any sealant fluid hence the pumping is dry.
High quality SS 304/316 material of construction ensures effective resistance to corrosive liquids & slurries and hence pumps made from this metal, undisputedly stands as an ultimate choice of every discerning user to resist the violent attacks of such hot and cold corrosive mediums in their process industries
.Applications »
Hot and cold chemical process service, thermic fluids, chemicals, petrochemicals, sugar, textiles, effluent, pharmaceuticals, labs and pilot plants.
The most sought after corrosive abrasion resistant pump made from compressed moulded inert polypropylene. Excellent for host of highly corrosive and hazardous pumping operations.
The pump is designed for back pull out. The complete rotor assembly can be pulled out if and when required for repairing and refitting there after without disturbing the casing, suction/delivery piping and the motor.
Application »
Chemicals, Pharmaceuticals, Petrochemicals, Fitilizer, Acid, Dyes, Organic and Inorganic Fluid, Paper, Textiles etc.
Magnetically driven, this is a wonder pump and is 100% guaranteed leak proof. The medium does not come in contact with shaft, hence no leakage at all. Pollution of course is out of question. Light weight - easy intallation - cost effectiveness-compact designing, portability-reliability, safety and above all chemical resistance are a few distinctive features of this special purpose popular device. These are best suited for photo cine plants, x-ray plants, filtration systems, photo processors, electroplating equipments, metal finishing machines, water treatment plants, descaling, chemical, photochemical & pharmaceutical industries etc.
Its non-clogging features combined with ability to handle liquids containing small solids have made it quite popular with electroplating units. Uniform consistency of highly abrasive chemicals is achieved and maintained through continuous vigorous stirring done by this unique pump. Consequently this adds to shine and gloss of the end product. Besides, it has also found favour with TV Tube manufacturing. Glass etching, Refrigeration, de-scaling, pharmaceutical industries. Chemical processing plants and photo film processing.
Single stage, horizontal, centrifugal, self priming, end suction, mud / sewage pumps are of non-clog type. These have semi-open type, dynamically balanced impeller for vibration free operation and hence have longer life.
These are best suited for applications where self priming action is required such as pumping water from docks, ports, vessels; pumping petroleum products, chemicals, effluent water, filter press; dewatering foundations, trenches & pits, sewage pumping etc.
Gear pumps are the most commonly used for handling and transferring any kind of viscous liquids.may these be petroleum and food products, dyes, syrups, corrosive chemicals, soaps, detergents. Starch asphalts, ink and paints etc.
These are highly efficient and low coast positive displacement pumps. These are available in both C.I and S. S material of construction.
Jacketed pumps are also available which are required for handling substances like wax, which needs to be turned into fluid prior to moving them.
Metering/Dosing pumps are plunger or diaphragm type positive displacement pumps used for feeding intermittently or continuously a controlled quantity of fluid / chemical within pre-determined time or at fixed intervals. Quantity of the dose time or intervening time can be regulated even while in operation.
These are in hot demand by chemical processors, pharmaceuticals, photo film, textile, cosmetics, petroleum, confectionery, detergent, beverages and host of similar industries.
Barrel pumps are suitably designed for safe effective and economic al transfer of liquids, chemical and petroleum products from drums and carboys. These are lightweight pumps and hence can be employed for stationary as well as portable services.
Can handle water, fruit, juices, salt, and soap solutions electroplating and other chemicals, acid.
Transfer of solvents, paints, petroleum products, pesticides and inflammable liquids can effectively be looked after by the models supplied with flameproof or pneumatic motors.
Twin chambered continuous Impregnation plant is specially designed to ensure high quality of Impregnation at a much faster rate than that of the conventional type. Here, both the chambers can perform turn by turn, the duties of an impregnating chamber and that of a storage tank, whereby we not only get increase in capacity, but can also save on time as well. Thus in a way, this fulfills the duty of a bigger plant.
Available in following standard models and can also be fabricated as per user's specific requirements.
Range:
Sr. No. |
Model |
Power HP |
Suction size( inch) |
Discharge size(inch) |
Max flow LPM |
Max Head in M |
1 |
SSBC-25/120 |
0.5 |
1 |
1 |
0 to 115 |
18 to 0 |
2 |
SSBC-25/138 |
1 |
1 |
1 |
0 to 220 |
24 to 0 |
3 |
SSBO-25/138 |
1 |
1 |
1 |
0 to 200 |
22 to 0 |
4 |
SSBC-25/142 |
1.5 |
1.5 |
1 |
0 to 325 |
24 to 0 |
5 |
SSBC-50/114 |
1 |
2 |
2 |
0 to 480 |
16 to 0 |
6 |
SSBC-40/114 |
2 |
2 |
1.5 |
0 to 420 |
24 to 0 |
7 |
SSBC-25/160 |
3 |
1.5 |
1 |
0 to 400 |
35 to 0 |
8 |
SSBC-25/180 |
5 |
1.5 |
1 |
0 to 600 |
50 to 0 |
9 |
CEMRON |
1 |
1 |
1 |
0 to 220 |
22 to 0 |
CEMRON MODEL IS MONOBLOCK CONSTRUCTION PUMPS COST OF ACCESSORIES LIKE BASE FRAME COUPLING, COUPLING GUARD CAN BE SAVED.OTHER PUMPD ARE BARE SHAFT .
Application
Range:
Sr. No. |
Model |
Motor Hp |
RPM |
Max Cap M3/Hr. |
Max Head in M |
Suction (mm) |
Discharge (mm) |
1 |
P-22-100-H |
1.00 |
2900 |
0 - 6.5 |
13 - 0 |
25 |
25 |
2 |
P-44-120-H |
2.00 |
2900 |
0 - 24 |
18 - 0 |
40 |
40 |
3 |
P-44-150-H |
3.00 |
2900 |
0 - 22 |
24 - 0 |
40 |
40 |
4 |
P-47-160-H |
5.00 |
2900 |
0 - 32 |
33 - 0 |
75 |
40 |
5 |
P-57-170-H |
7.50 |
2900 |
0 - 60 |
34 - 0 |
75 |
50 |
6 |
P-47-210-L |
3.00 |
1440 |
0 - 33 |
15 - 0 |
75 |
40 |
7 |
P-45-190-H |
10.00 |
2900 |
0 - 58 |
49 - 0 |
50 |
40 |
8 |
P-57-210-L |
5.00 |
1440 |
0 - 52 |
16 - 0 |
75 |
50 |
9 |
P-57-185-H |
20.00 |
2900 |
0 - 96 |
42 - 0 |
75 |
50 |
10 |
P-44-205-L |
2.00 |
1440 |
0 - 26 |
12 - 0 |
40 |
40 |
FIRST PHOTOGRAPH IS FOR MONOBLOCK CONSTRUCTION PUMPS
Cost Of Accessories Like Base Frame, Coupling, Coupling Guard Can Be SavedSECOND PHOTOGRAPH IS FOR BARE SHAFT
THIRD PHOTOGRAPH FOR VERTICAL PUMP IN 500MM, 1000MM, 1500 MM LENGTH
SPARES PARTS LIST: |
|
|
SR .NO |
DESCREPTION |
M.O.C |
1 |
VALUTE CASING |
P.P |
2 |
BACK PLATE |
P.P |
3 |
IMPELLER |
P.P |
4 |
SUCTION FLANGE |
P.P |
5 |
ADOPTER |
C.I. |
6 |
CAGE RING |
C.I |
7 |
HARDWARE SET FOR VOLUTE ASSLY. |
SS |
COMMON TO ALL |
|
|
8 |
FLANGE FOR BACKPLATE |
P.P |
9 |
BUSH |
GFT |
10 |
DRIP - TRAY |
FRP |
11 |
STAIONARY RING FOR MACHSEAL -1 3/8" |
CERAMIC |
12 |
LOCATION FLANGE |
BACK PLATE |
13 |
PP COTAED NUT - 3/8" BSW |
PP/MS |
14 |
LEG SUPPORT FOR BEARING HOUSE |
C.I |
15 |
BALL BEARING 3306 MOTOR SIDE |
STD |
16 |
CIR.CLIP |
STEEL |
17 |
OIL SEAL 40X25X10 MOTOR SIDE |
NEOPRENE |
18 |
LOCK NUT WITH LOCK WAHSER |
STEEL |
19 |
BARE SHAFT |
EN 8 |
20 |
BEARING COVER |
C.I |
21 |
BEARING HOUSING |
C.I |
22 |
BALL BEARING 6207 PUMP SIDE |
STD |
23 |
OIL SEAL 35X72X10 PUMP SIDE |
NEOPRENE |
24 |
DEFLACTOR |
PP/MS |
25 |
SHAFT SLEEVE FOR 1 3/8" SEAL |
CERAMIC |
26 |
ROTARY UNIT FOR MACHSEAL |
TEF. BELLOWS |
27 |
WASHER FOR STAIONARYPART OF MACHSEAL |
PTFE |
28 |
BOLTS FOR LOCATION FLANGE |
SS-316 |
29 |
"O" RING |
VITION |
FOR GLAND PACKING ARRANGMENT |
|
|
35 |
GLAND RING ( ONE SET = 4 RING ) |
GRAFIED FILL TEFLON |
36 |
GLAND PUSHER |
BACKELITE |
37 |
GLAND HOUSE |
GFT |
38 |
LOCATION FLANGE |
BACKELITE |
39 |
BACK PLATE WITH BUSH FOR GLAND SET |
PP |
Range:
MODEL | Motro HP |
RPM |
Flow Range LPH |
Press kg/cm2 |
MOJPD10 |
0.25 |
1440 |
3.5 to 86 |
0 to 47 |
MOJPD20 |
0.5 |
1440 |
7 to 544 |
0 to 300 |
MOJPD30 |
1 |
1440 |
11 to 1540 |
0 to 300 |
MOJPD40 |
1.5 |
1440 |
20 to 3000 |
0 to 300 |
MOJPD60 |
2 |
1440 |
48 to 6134 |
0 to 300 |
MOJPD90 |
3 to 10 |
1440 |
200 to 14378 |
0 to 300 |
Range:
Model |
Motor HP |
RPM |
Phase |
Max Flow in LPM |
Max Head in M |
Suction |
Discharge |
MMP-1 |
3/16 |
2800 |
1 |
15 |
2.4 |
14 mm |
14 mm |
MMP-2 |
1/4 |
2800 |
1 |
30 |
3.4 |
18 mm |
18 mm |
MMP-3 |
5/16 |
2800 |
1 |
50 |
4 |
20 mm |
20 mm |
MMP-4 |
3/8 |
2800 |
1 & 3 |
80 |
6 |
25 mm |
25 mm |
MMP-5 |
1/2 |
2800 |
1 & 3 |
115 |
10 |
25 mm |
25 mm |
MMP-7 |
1.50 |
2800 |
3 |
280 |
20 |
1.5" bsp F |
1.25" Bsp M |
MMP-6 |
3.00 |
2800 |
3 |
520 |
25 |
2" npt F |
1.5" npt M |
Application
Range:
Model | Motor HP |
Wt |
Max Flow |
Max Head |
Max Viscosity |
Low Viscous Drum Pump - Electric Driven, Nno Flp |
|
|
|
|
|
MOA 40E/0.5 |
350 W/1 Phase |
8 Kg |
60 lpm |
8 M. |
150 cps |
MOA 40E/1.0 |
700 W/1 Phase |
8 Kg |
70 lpm |
12 M. |
300 cps |
MOA 40E/1.5 |
1050 W/1 Phase |
8 Kg |
100 lpm |
18 M. |
500 cps |
|
|
|
|
|
|
Low Viscous Drum Pump - Air Driven |
|
|
|
|
|
MOA 40A/0.6 |
0.6 HP/18 CFM@3-6 Bar |
6 Kg |
90 lpm |
15 M. |
300 cps |
High Viscous Drum Pump - Electric Driven, Non Flp |
|
|
|
|
|
MOA 40 E HVS/1.0 |
1.0 HP/960 RPM/3 Phase |
18 Kg |
50 Kg/Min. |
8 Bar |
10000 cps |
MOA 40E HVS/ 1.5 |
1.5 HP/960 RPM/3 Phase |
18 Kg |
30 Kg/Min. |
8 Bar |
3000 cps |
MOA 40E HVS/ 2.0 |
2.0 HP/960 RPM / 3Phase |
24 Kg |
15 Kg/Min. |
8 Bar |
30000 cps |
High Viscous Drum Pump - Air Driven |
|
|
|
|
|
MOA 40 HVS/1.2 |
1.2 HP/30 CFM@3-6 Bar |
12 Kg |
30 Kg/Min. |
8 M. |
15000 cps |
Application
Range:
Model |
Suc*Del Size In mm |
Max Capacity m3/hr |
Max Head in Metre |
Model |
Suc*Del Size In mm |
Max Capacity m3/hr |
Max Head in Metre |
MOBP 32/13 |
50*32 |
22 |
24 |
MOBP 65/20 |
80*65 |
155 |
65 |
MOBP 32/16 |
50*32 |
24 |
40 |
MOBP 65/26 |
80*65 |
160 |
99 |
MOBP 32/20 |
50*32 |
26 |
64 |
MOBP 65/32 |
80*65 |
90 |
37 |
MOBP 32/26 |
50*32 |
30 |
103 |
MOBP 80/16 |
100*80 |
210 |
42 |
MOBP 40/13 |
65*40 |
38 |
25 |
MOBP 80/20 |
100*80 |
247 |
65 |
MOBP 40/16 |
65*40 |
41 |
39 |
MOBP 80/26 |
100*80 |
240 |
100 |
MOBP 40/20 |
65*40 |
42 |
63 |
MOBP 80/32 |
100*80 |
145 |
32 |
MOBP 40/26 |
65*40 |
43 |
96 |
MOBP 100/20 |
125*100 |
350 |
63 |
MOBP 50/13 |
65*50 |
80 |
26 |
MOBP 100/26 |
125*100 |
380 |
98 |
MOBP 50/16 |
65*50 |
90 |
41 |
MOBP 100/32 |
125*100 |
180 |
37 |
MOBP 50/20 |
65*50 |
84 |
65 |
MOBP 100/40 |
125*100 |
200 |
56 |
MOBP 50/26 |
65*50 |
84 |
100 |
MOBP 125/26 |
150*125 |
320 |
23 |
MOBP 65/13 |
80*65 |
127 |
26 |
MOBP 125/32 |
150*125 |
270 |
37 |
MOBP 65/16 |
80*65 |
142 |
41 |
MOBP 125/40 |
150*125 |
360 |
59 |
Application
Range:
Model |
Rec. Motor (Hp) |
Discharge LPS |
Head M |
Suc * Dis (mm) |
Speed (RPM) |
MOSPM 101 |
1 (1 Ø, 3 Ø) |
0 to 6.2 |
15 to 0 |
40 * 40 |
2850 |
MOSPM 102 |
2 (3 Ø) |
0 to 9.2 |
22 to 0 |
40 * 40 |
2850 |
MOSPM 103 |
3 (3 Ø) |
0 to 12 |
26 to 0 |
50 * 50 |
2900 |
MOSPM 104 |
5 (3 Ø) |
0 to 20 |
32 to 0 |
80 * 80 |
2900 |
MOSPM 104 S |
7.5 (3 Ø) |
0 to 23 |
36 to 0 |
80 * 80 |
2900 |
MOSPM 105 |
5 (3 Ø) |
0 to 20 |
18 to 0 |
80 * 80 |
1450 |
MOSPM 106 |
10 (3 Ø) |
0 to 40 |
26 to 0 |
100 * 100 |
1450 |
MOSPM 106 S |
12.5 (3 Ø) |
0 to 45 |
28 to 0 |
100 * 100 |
1450 |
MOSPM 107 |
20 (3 Ø) |
0 to 72 |
25 to 0 |
150 * 150 |
1450 |
MOSPM 107 S |
25 (3 Ø) |
0 to 80 |
28 to 0 |
150 * 150 |
1450 |
Application
PORTABLE SUBMERSIBLE SEWAGE PUMP
Range:
Model |
H.P |
Motor |
Phase |
Capcacity in Lpm |
Head in mm |
Dis.Size in mm |
Solid Handled. Size mm |
MOPSSF-0.5 |
0.5 |
2900 |
1 |
0 to 260 |
12 to 0 |
50 |
25 |
MOPSSF-1.0 |
1 |
2900 |
1 |
0 to 550 |
13 to 0 |
50 |
25 |
MOPSSF-1.5 |
1.5 |
2900 |
1 |
0 to 600 |
14 to 0 |
50 |
25 |
MOPSSF-2.0 |
2 |
2900 |
1 |
0 to 700 |
16 to 0 |
75 |
25 |
MOPST-3.0 |
3 |
2900 |
3 |
0 to 750 |
22 to 0 |
75 |
25 |
MOPST-5.0 |
5 |
2900 |
3 |
0 to 960 |
24 to 0 |
75 |
25 |
MOPST-7.5 |
7.5 |
2900 |
3 |
0 to 1400 |
26 to 0 |
100 |
25 |
Range:
Model |
H.P |
Motor |
Phase |
Capcacity in Lpm |
Head in mm |
Dis.Size in mm |
Solid Handled. Size mm |
MOPSSF-0.5 |
0.5 |
2900 |
1 |
0 to 260 |
12 to 0 |
50 |
25 |
MOPSSF-1.0 |
1 |
2900 |
1 |
0 to 550 |
13 to 0 |
50 |
25 |
MOPSSF-1.5 |
1.5 |
2900 |
1 |
0 to 600 |
14 to 0 |
50 |
25 |
MOPSSF-2.0 |
2 |
2900 |
1 |
0 to 700 |
16 to 0 |
75 |
25 |
MOPST-3.0 |
3 |
2900 |
3 |
0 to 750 |
22 to 0 |
75 |
25 |
MOPST-5.0 |
5 |
2900 |
3 |
0 to 960 |
24 to 0 |
75 |
25 |
MOPST-7.5 |
7.5 |
2900 |
3 |
0 to 1400 |
26 to 0 |
100 |
25 |
Range:
Model |
H.P |
Motor |
Phase |
IN M3/HR |
IN MT |
Dis.Size in mm |
Solid Handled. Size in mm |
MONS10.0/6P/1 |
10 |
950 |
3 |
25-200 |
14.8-8.2 |
100 |
25 |
MONS15.0/6P/1 |
15 |
950 |
3 |
50-300 |
15-7 |
150 |
25 |
MONS20.0/6P/1 |
20 |
950 |
3 |
50-500 |
16-10 |
150 |
25 |
MONS30.0/6P/1 |
30 |
950 |
3 |
50-600 |
18-10 |
200 |
25 |
MONS10.0 |
10 |
1400 |
3 |
10-140 |
18.4-10 |
100 |
25 |
MONS15.0/1 |
15 |
1400 |
3 |
10-240 |
23.6-8.4 |
100 |
25 |
MONS20.0/1 |
25 |
1400 |
3 |
20-240 |
24-12.4 |
100 |
25 |
MONS30.0/1 |
30 |
1400 |
3 |
20-260 |
28.4-17 |
150 |
25 |
Range:
Model |
H.P |
Motor |
Phase |
Capcacity in Lpm |
Head in m |
Dis.Size in mm |
Solid Handled. Size in mm |
MOD-3/10.0 |
10 |
2900 |
3 |
500-2150 |
24-14 |
150 |
25 |
MOD-3/15.0 |
15 |
2900 |
3 |
1050-2500 |
28-16 |
150 |
25 |
MOD-3/25.0 |
25 |
2900 |
3 |
1100-2750 |
32-18 |
150 |
25 |
MOD-3/30.0 |
30 |
2900 |
3 |
1200-3500 |
32-20 |
150 |
25 |
Application
Materials:
PASWARA IMPEX is engaged in the manufacturing and supply of Engineering Goods, Machinery Parts, Electrical Motors, Fabrication of Machinery Parts, Pressure Vessels, Heat Exchangers, Tanks, Reactors and Special Type Components.